Numerical analysis of the effect of material type on heat dissipation ducts in parabolic fin application
, ,
1Low/Zero Carbon Energy Technologies Laboratory, Faculty of Engineering and Architecture, Recep Tayyip Erdogan University, Zihni Derin Campus, 53100 Rize, Turkey
2Department of Architecture, Faculty of Engineering and Architecture, Recep Tayyip Erdogan University, Zihni Derin Campus, 53100 Rize, Turkey
Heating due to continuous operation in electronic devices is a common problem. Especially the decrease in the size of the devices produced with new possibilities makes this situation more complicated. Although it is possible for medium and large-sized devices to predominantly use forced convection for cooling, this is not possible as device sizes get smaller. In this case, the use of expanded surfaces is common. With the application called fin, the surface area for heat dissipation is expanded and more heat is removed from the device. In this study, the effect of the use of aluminium, brass, and iron on parabolic fin performance in an unconventional parabolic fin application is discussed with the CFD model created. Recommendations are made to the manufacturers by interpreting how the change in material properties affected the heat discharge.
AlEssa, AH, and Al-Odat, MQ, 2009. Enhancement of natural convection heat transfer from a fin by triangular perforations of bases parallel and toward its base. The Arbian Journal for Science and Engineering, 34(2).
Bar-Cohen, A, 1979. Fin thickness for an optimized natural convection array of rectangular fins.
Cengel, YA, 2000. Heat and mass transfer.
Cuce, E and Cuce, PM, 2015. A successful application of homotopy perturbation method for efficiency and effectiveness assessment of longitudinal porous fins. Energy Conversion and Management, 93, 92-99.
Cuce, PM, Cuce, E, and Sen, H, 2022. 'Numerical investigation of barrier effect with air, argon and krypton gases in double glazing application'. In: Riffat, Su,. ed., Sustainable Energy Technologies: Proceedings of the 19th International Conference on Sustainable Energy Technologies, 16th – 18th August 2022, Turkey. University of Nottingham: Buildings, Energy & Environment Research Group. Pp 355-362. Available from: nottingham-repository.worktribe.com/ [14.07.2023].
Incropera, FP, DeWitt, DP, Bergman, TL, and Lavine, AS, 1996. Fundamentals of heat and mass transfer (Vol. 6, pp. 408-409). New York: Wiley.
Jones, CD. and Smith, LF, 1970. Optimum arrangement of rectangular fins on horizontal surfaces for free-convection heat transfer.
Kiwan, S and Al-Nimr, MA, 2001. Using porous fins for heat transfer enhancement. J. Heat Transfer, 123(4), 790-795.
Ma, SW, Behbahani, AI, and Tsuei, YG, 1991. Two-dimensional rectangular fin with variable heat transfer coefficient. International Journal of Heat and Mass Transfer, 34(1), 79-85.
Mueller Jr, DW, and Abu-Mulaweh, HI, 2006. Prediction of the temperature in a fin cooled by natural convection and radiation. Applied Thermal Engineering, 26(14-15), 1662-1668.
Sen, H, Cuce, E, and Cuce, PM, 2023. ‘Numerical analysis of the effect of groove geometry on fin performance in rectangular fin design’, in ICHEAS 4th International Conference On HEALTH, ENGINEERING AND APPLIED Sciences, 14-16 April, Dubai.
Sobhan, CB, Venkateshan, SP, and Seetharamu, KN, 1990. Experimental studies on steady free convection heat transfer from fins and fin arrays. Waerme-und Stoffuebertragung;(Germany, FR), 25(6).
Starner, KE and McManus Jr, HN, 1963. An experimental investigation of free-convection heat transfer from rectangular-fin arrays.
Tari, I. and Mehrtash, M, 2013. Natural convection heat transfer from inclined plate-fin heat sinks. International journal of heat and mass transfer, 56(1-2), 574-593.
He, Z, Yan, Y, and Zhang, Z, 2021. Thermal management and temperature uniformity enhancement of electronic devices by micro heat sinks: A review. Energy, 216, 119223.
How to cite this article
Cuce, E., Cuce, P.M. and Sen, H. (2023). 'Numerical analysis of the effect of material type on heat dissipation ducts in parabolic fin application'. SET Proceedings, 20(2), pp. 137-143. https://doi.org/10.65582/set.2023.066